Tuo, Biyang Shi, Xiulong Tian, Jinwang Wang, Jianli
Published in
Materials Science-Poland
To broaden the light response range of TiO2 and improve its photocatalytic activity, BiOCl/TiO2/MMT composite materials (BTMC) with outstanding photocatalytic performance were prepared by the sol-gel method with montmorillonite (MMT) as the supporting material, tetrabutyl titanate as titanium source and, bismuth nitrate pentahydrate as the bismuth ...
Martínez-Hernández, Miryam Manzo-García, Daniel Ramírez-Ortega, Juana Paulina Arreguín-Cano, Juan Antonio Chávez-Cortéz, Elda Georgina Arenas-Alatorre, Jesús Ángel Rodríguez-Chávez, Jacqueline Adelina Flores-Ledesma, Abigailt
Published in
Materials Science-Poland
In medicine, bismuth is used as an antimicrobial agent. In dentistry, it is used primarily to increase radiopacity in some endodontic materials. The objective is to evaluate the antimicrobial activity, cell viability, pH, solubility, film thickness, and setting time of a mineral trioxide aggregated (MTA)-types of cement with different concentration...
Bieliatynskyi, Andrii Yang, Shilin Krayushkina, Kateryna Shao, Meiyu Ta, Mingyang
Published in
Materials Science-Poland
The introduction of new effective road construction materials for pavements and foundations of highways is an urgent task, including the development and application of resource-saving technologies aimed at the use of low-demand, large-tonnage mineral materials, semi-finished products, industrial waste, and their by-products. Research on this topic ...
Paengchit, Phacharadit Saikaew, Charnnarong
Published in
Materials Science-Poland
Tool life performances of Al2O3+TiC and TiN+AlCrN tool inserts were investigated experimentally under different cutting conditions in turning AISI 4140 steel. The tool life model is defined in accordance with a maximum surface roughness of 0.8 μm for the tool life criterion. The relationships between machining factors (i.e., cutting speed and feed ...
Jian, Li
Published in
Materials Science-Poland
This work studied the surface, interface state and physicochemical properties of HNO3-treated and KOH-treated carbon fiber. Poly(methyl methacrylate) (PMMA) composites were prepared by the autoclave molding process using surface-treated carbon fiber as reinforcements. The physical and chemical states of the carbon fiber surfaces and the micro-inter...
Kannan, P.R. Thanigaivelan, R Thiraviam, R Pradeep Kumar, K
Published in
Materials Science-Poland
Aluminium-based hybrid nano-metal matrix composites are right materials, finding application in the aerospace and automotive industry. The present research focused on the effects of sliding load, sliding velocity, and temperature on wear behaviour of a novel hybrid metal matrix nano-composite .Stir-squeeze casting setup is used to produce the compo...
Khawaji, Mohammad
Published in
Materials Science-Poland
Geopolymers have gained attention as a potential eco-friendly alternative to Portland cement, primarily due to their reduced carbon dioxide emissions and the opportunity to repurpose industrial waste materials. Fly ash (FA), a byproduct of coal combustion, has been favored as a raw material for geopolymer concrete owing to its widespread availabili...
Fu, Lijuan Fan, Shuxing Wang, Zhao Tang, Wei
Published in
Materials Science-Poland
A double-jet electrospinning method was adopted to fabricate In2O3/Co3O4 nanofibers (NFs). The sensitivity of In2O3/Co3O4 NFs and In2O3 NFs were compared and analyzed, and the morphology, structure, chemical composition, and gas-sensing properties of the samples were comprehensively characterized. The results show that the introduction of Co3O4 can...
Sakthi, S. Mahendran, S. Meignanamoorthy, M. Mohanavel, V.
Published in
Materials Science-Poland
Magnesium composites are innovative, compact, and distinctive materials. Because of their low density, magnesium composites are suitable for applications in the automobile, aviation, semiconductor, and pharmaceutical sectors. To enhance the mechanical wear and corrosion behavior of theAZ61 Mg alloy, different weight percentages of nano-B4C reinforc...
Korzeniowski, Marcin Małachowska, Aleksandra Wiatrzyk, Marta
Published in
Materials Science-Poland
The quality of the powder layers in the 3D printing process is extremely important and directly corresponds to the quality of the structures made with this technology. Therefore, it is essential to control it. It can be made in-line with a vision system combined with image processing algorithms, which can significantly improve control of the proces...