Gawryluk, Jarosław Bocheński, Marcin Teter, Andrzej
Published in
Archive of Mechanical Engineering
In the paper, the authors discuss the numerical and experimental modal analysis of the cantilever thin-walled beams made of a carbon-epoxy laminate. Two types of beams were considered: circumferentially asymmetric stiffness (i.e., CAS) and circumferentially uniform stiffness (i.e., CUS) beams. The layer-up configurations of the laminate were chosen...
Arya, Amir Shahmiry, Saeed Nikkhah, Vahid Sarafraz, Mohamad Mohsen
Published in
Archive of Mechanical Engineering
Experimental investigation was conducted on the thermal performance and pressure drop of a convective cooling loop working with ZnO aqueous nanofluids. The loop was used to cool a flat heater connected to an AC autotransformer. Influence of different operating parameters, such as fluid flow rate and mass concentration of nanofluid on surface temper...
Mashat, D. S. Zenkour, A. M. Abouelregal, A. E.
Published in
Archive of Mechanical Engineering
In the present article, we introduced a new model of the equations of generalized thermoelasticity for unbounded orthotropic body containing a cylindrical cavity. We applied this model in the context of generalized thermoelasticity with phase-lags under the effect of rotation. In this case, the thermal conductivity of the material is considered to ...
Ingole, Sunil B. Sundaram, K. K.
Published in
Archive of Mechanical Engineering
Inclined jet air cooling can be effectively used for cooling of electronics or other such applications. The non-confined air jet is impinged and experimentally investigated on the hot target surface to be cooled, which is placed horizontally. Analysis and evaluations are made by introduction of a jet on the leading edge and investigated for downhil...
Ghafoor Elahi, Mohammad Reza Rokhi, Masoud Mahdizadeh
Published in
Archive of Mechanical Engineering
In this article, the fracture behavior of functionally graded thick-walled cylinder under thermo-mechanical shock is investigated. For this purpose, classical coupled thermoelastic equations are used in calculations. First, these equations are discretized with extended finite element method (XFEM) in the space domain and then they are solved by the...
Zare, Shahryar Tavakolpour-Saleh, Alireza Omidvar, Amir
Published in
Archive of Mechanical Engineering
In this paper, pole placement-based design and analysis of a free piston Stirling engine (FPSE) is presented and compared to the well-defined Beale number design technique. First, dynamic and thermodynamic equations governing the engine system are extracted. Then, linear dynamics of the free piston Stirling engine are studied using dynamic systems ...
Allam, M. N. M. Tantawy, R. Yousof, A. Zenkour, A. M.
Published in
Archive of Mechanical Engineering
Analytical and numerical nonlinear solutions for rotating variable-thickness functionally graded solid and annular disks with viscoelastic orthotropic material properties are presented by using the method of successive approximations.Variable material properties such as Young’s moduli, density and thickness of the disk, are first introduced to obta...
Rajesh, Korabathina Saheb, Koppanati Meera
Published in
Archive of Mechanical Engineering
Complex structures used in various engineering applications are made up of simple structural members like beams, plates and shells. The fundamental frequency is absolutely essential in determining the response of these structural elements subjected to the dynamic loads. However, for short beams, one has to consider the effect of shear deformation a...
Bhirud, N.L. Gawande, R.R.
Published in
Archive of Mechanical Engineering
During the machining processes, heat gets generated as a result of plastic deformation of metal and friction along the tool–chip and tool–work piece interface. In materials having high thermal conductivity, like aluminium alloys, large amount of this heat is absorbed by the work piece. This results in the rise in the temperature of the work piece, ...
Bielawski, Radosław Kowalik, Michał Suprynowicz, Karol Rządkowski, Witold Pyrzanowski, Paweł
Published in
Archive of Mechanical Engineering
The aim of the paper is to validate the use of measurement methods in the study of GFRP joints. A number of tests were carried out by means of a tensile machine. The studies were concerned with rivet connection of composite materials. One performed two series of tests for two different forces and two fibre orientations. Using Finite Element Method ...